![]() 10.15.5 update worked without any issues (applied 14-June-2020) updated Lilu/WEG and then Clover first. ![]() 10.15.4 supplemental update worked without any issues (applied 1).Don't be alarmed by this as it will work correctly anyway. The controller shows up as a PCIe device rather than a USB controller. If you add the Inateck USB 3.0 controller card like I did it will work OOB but will not show up as available USB ports in Hackintool or USBMap tool. I was unable to get them to work properly with USB 3.0 enabled as the Renesas drivers don't work on Catalina. The left-most port on the front panel will no longer work and the three on the bottom rear will no longer work. I recommend that you disable USB 3.0 ports in the BIOS and then use the USB injector kext from this repo or create your own using Hackintool. NOTE: This section is outdated and not very useful currently so have a look at the SSDTs and USB injector kext in the latest EFI for how I find best to approach port mapping with current OC and Big Sur. USB mapping Requires resetting RHUB and a few renames.CPU power management info for YOUR processor (use Piker Alpha's SSDT generator) to create appropriate power management settings for your hardware.SMBIOS details (serial number, MLB, UUID).If you're using the OpenCore EFI, you'll need to change at least the following: If you're using the Clover EFI, you shouldn't need to change much beyond adding SMBIOS details (serial number, etc). ![]() You'll also need to add SMBIOS information (serial number, board serial number, UUID) as they've been removed from my ist to protect my Apple ID. If you're not using an AMD GPU, expect a bunch of changes to be required, too. Chances are you'll have a different CPU at the very least which may require some changes. My system has a Renesas USB 3.0 controller which is a pain in the ass to get to work (have yet to figure that out but supposedly it's possible). You should modify the EFI (a lot) if your system specs are different. Tested on macOS Catalina 10.15.5 (vanilla) and Big Sur 11.4 (vanilla).Legacy ROM disabled (required for the Quadro but not for the Radeon).Disks set to AHCI mode (default is RAID).Enable VT for Direct I/O disabled (Virtualization Support can be enabled if you need it for Docker, etc).You can find screenshots of the BIOS configuration options I used in Screenshots/BIOS. Logitech M590 (connected using Logitech Unified receiver) Logitech MX Keys (connected via Bluetooth) Microsoft Surface (connected via Bluetooth) Inateck KT4006 2-port PCI-E USB 3.0 Express Card Renesas uPD720201 USB 3.0 Host Controller Rankie 4k DP to HDMI cable (CableMatters adapter didn't work well) Budget Dell Precision T3610 Xeon Build (~$350)Ĭlover and OpenCore EFI folders required for a Dell Precision T3610 hackintosh running macOS Catalina (up to 10.15.7) or Big Sur (up to 11.4). ![]() I improved things a bit by switching to OpenCore the X79 guide took me the rest of the way. Before finding this I had a usable machine but performance wasn't great. If this helps you, thank mighil and maldon since they did the hard work (and the many others who gave us Clover, OpenCore, kexts, etc)! stole this from mighil because it's right on Note: You're nothing but an a-hole if you sell EFI folder (config) that's readily available for free. Dell Precision T3610 Workstation Hackintosh That being said, if you have any issues with using it or with your Precision Workstation feel free to email or open an issue and I'll gladly try to help you. ⚠️ I no longer have this machine so active updates to either the Clover or OC EFIs is unlikely.
0 Comments
Leave a Reply. |